Cookies sur les sites Web Omega
Nous utilisons des cookies sur ce site Web. Ces cookies sont indispensables au bon fonctionnement de notre site.
Si vous continuez sans modifier vos paramètres, nous supposerons que vous êtes heureux de recevoir tous les cookies de notre site Web.
Pour de plus amples informations à ce sujet, veuillez cliquer ici
Fermer
Panier  |  Contact  | 
NUMÉRO VERT 0805 541 038
INTERNATIONAL+33 01 57 32 48 17
Layer N Banner

High Performance Stepper Drives With Advanced Features And Control Options

ST Series

Stepper Drives | ST Series

Stepper Drives

Garantie 1 an
  • Current Output 0.5 to 10.0 A
  • Configurable Idle Current Reduction
  • Pulse and Direction
  • Analog Command Signal
  • Serial Commands Via RS232/485/Ethernet
  • Stand-Alone Programming on "Si", "IP", and "Plus" Models
  • Microstepping up to 51,200 Steps per Revolution
  • Fault Protection:
      – Over-Voltage, Under-Voltage
      – Over-Temp
      – External Output Shorts
      – Internal Amplifier Shorts
  • All Models Compatible With Multi-Axis Controller HUB 444
  • Sample Motion Programs Available by Request
Variateurs et moteurs - Voir Les Produits Associés

Déscription

The ST-series high performance stepper drives incorporate advanced features that will derive the highest performance from today’s stepper motors. The Anti-Resonance and Waveform Damping control algorithms make this drive a clear market leader. The "-S" models are step and direction drives, compatible with PLCs which feature high-speed pulse output, such as our ELC-PLC series and OCS XL series. The "-Si" models are stand-alone programmable drives which are programmed with the simple-to-use Si Programmer software. Both the "-S" and "-Si" models can be controlled by sending serial commands in a simple ASCII format, the Si Command Language (SCL). SCL allows for control via serial commands sent from a host device such as a PC or PLC. This permits the user to perform a variety of motion, I/O, and system status tasks in real time via a host serial device.

Some of the advanced features of the ST-series drives include:

Self Test and Auto Setup: At start-up the drive measures motor parameters, including the resistance and inductance, then uses this information to optimize the system performance. It also compares this information from the last configuration and checks to see if the motor data has changed (this could indicate a fault or system change). The drive can also detect open and short circuits.

Anti-resonance: A disadvantage of the step motor is a tendency to "resonate" at some frequency. By entering some system data this natural frequency can be calculated and a damping term entered into the control algorithm. This significantly improves midrange stability and allows higher speeds and more use of the available torque.

Command Signal Smoothing: Dynamic smoothing can soften the effect of immediate changes in velocity and direction, making the motion of the motor less jerky. An added advantage is that it can reduce the wear on mechanical components.

Torque Ripple Smoothing: All step motors have an inherent low speed torque ripple that can affect the motion of the motor. By analyzing this torque ripple the system can apply a negative harmonic to negate this effect, giving the motor much smoother motion at low speed. br>
Si Programmer
Intended for use in stand-alone applications, Si (Simple Indexer) Programmer provides quick, out-of-the-box use with an extremely friendly, point-and-click graphical interface that does not require any software programming experience. Once an Si program has been constructed and downloaded to the drive, the program can be executed stand-alone at power-up or from an external trigger. Constructing a program is accomplished through the use of instructions selected in a point-and-click manner. Once an instruction is selected, a "fill in the blanks" format is used to input parameters.

Constructing an Si program requires no prior programming experience nor does it require learning a programming language. Si Programmer generates the actual motion control program, based on user selected parameters, thereby eliminating syntax errors. Once created, programs are easily downloaded, uploaded, saved and printed.

Si Programmer also provides the capability to control digital inputs and outputs, useful for interfacing with external equipment like PLCs, sensors, end-of-travel switches, and more. Si Programmer has found success in all types of applications, from simple linear actuator applications to complete machine control with operator interface applications.

Q Programmer
Q Programmer is a text-based single-axis motion control software for "Plus", "Q", and "IP" model stepper drives. The software allows users to create sophisticated and functional programs that Plus, Q, and IP drives can run stand-alone. The commands available in the Q programming environment consist of commands for controlling motion, inputs and outputs, drive configuration and status, as well as math operations, register manipulation, conditional programming, and multi-tasking. Unlike the Si Programmer, some programming experience is recommended to use Q Programmer.

Protect your power supply from motor regeneration with the OMRC-050 regen clamp... see "Specs" above for details.
Placez votre commande(Veuillez spécifier la référence du produit)

Ce que d'autres personnes ont acheté: quand vous voyez cette icône, cliquez dessus pour afficher une liste des produits que d'autres personnes ont achetés en plus de ce modèle.

Code d'article/ Desc.
Qté
Déscription
ST5 Models: 5 Amp drives
  
ST5-S
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with 5 A/phase output
  
ST5-Plus
562.69
Stock: 3 semaines
 
Performance stepper drive with Q Programmer™
  
ST5-IP-EN
948.66
Stock: 1 semaine
 
Performance stepper drive with Q Programmer™ and Ethernet/IP
  
ST5-IP-EE
1,022.00
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet/IP plus encoder input
  
ST5-Q-EN
882.48
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet
  
ST5-Q-EE
988.51
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet plus encoder input
  
ST5-Q-NF
897.17
Stock: 4 semaines
 
Performance stepper drive with Q Programmer™ and encoder input/output
  
ST5-Si
764.82
Stock: 5 semaines
 
Performance stepper drive with Si Programmer™
  
ST5-Si-ENC
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and encoder input
  
ST5-Si-485
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and RS485 interface
  
ST5-Si-ENC-485
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and encoder input plus RS485 interface
  
ST5-Si-NF
956.01
Stock: 7 semaines
 
Performance stepper drive with Si Programmer™ and encoder input/output
ST10 Models: 10 Amp drives
  
ST10-S
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with 10 A/phase output
  
ST10-Plus
691.28
Stock: 3 semaines
 
Performance stepper drive with Q Programmer™
  
ST10-IP-EN
1,022.00
Stock: 1 semaine
 
Performance stepper drive with Q Programmer™ and Ethernet/IP
  
ST10-IP-EE
1,136.00
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet/IP plus encoder input
  
ST10-Q-EN
1,030.00
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet
  
ST10-Q-EE
1,133.00
Stock: 5 semaines
 
Performance stepper drive with Q Programmer™ and Ethernet plus encoder input
  
ST10-Q-NF
867.78
Stock: 1 semaine
 
Performance stepper drive with Q Programmer™ and encoder input/output
  
ST10-Si
904.54
Stock: 5 semaines
 
Performance stepper drive with Si Programmer™
  
ST10-Si-ENC
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and encoder input
  
ST10-Si-485
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and RS485 interface
  
ST10-Si-ENC-485
Consultez le Service de ventes  
Stock: 
 
 
Performance stepper drive with Si Programmer™ and encoder input plus RS485 interface
  
ST10-Si-NF
992.77
Stock: 7 semaines
 
Performance stepper drive with Si Programmer™ and encoder input/output
RECOMMENDED MOTORS FOR ST5 MODELS
  
OMHT17-075
114.28
Stock: 11 semaines
 
NEMA 17, 62.8 oz-in holding torque
  
OMHT17-275
83.83
Stock: 5 semaines
 
NEMA 17, 62.3 oz-in holding torque
  
OMHT17-278
99.11
Stock: 3 semaines
 
NEMA 17, 113 oz-in holding torque
  
OMHT23-397
Consultez le Service de ventes  
Stock: 
 
 
NEMA 23, 177 oz-in holding torque
  
OMHT23-597
110.41
Stock: 9 semaines
 
NEMA 23, 177 oz-in holding torque
  
OMHT23-400
Consultez le Service de ventes  
Stock: 
 
 
NEMA 23, 264 oz-in holding torque
  
OMHT23-600
168.17
Stock: 5 semaines
 
NEMA 23, 264.8 oz-in holding torque
  
OMHT24-100
111.34
Stock: 5 semaines
 
NEMA 24, 123 oz-in holding torque
  
OMHT24-105
126.00
Stock: 5 semaines
 
NEMA 24, 177 oz-in holding torque
  
OMHT24-108
224.15
Stock: 5 semaines
 
NEMA 24, 354 oz-in holding torque
RECOMMENDED MOTORS FOR ST10 MODELS
  
OMHT23-603
184.60
Stock: 3 semaines
 
NEMA 23, 354 oz-in holding torque
  
OMHT24-100
111.34
Stock: 5 semaines
 
NEMA 24, 123 oz-in holding torque
  
OMHT24-105
126.00
Stock: 5 semaines
 
NEMA 24, 177 oz-in holding torque
  
OMHT24-108
224.15
Stock: 5 semaines
 
NEMA 24, 354 oz-in holding torque
  
OMHT34-504
167.02
Stock: 5 semaines
 
NEMA 34, 396 oz-in holding torque
  
OMHT34-485
424.84
Stock: 1 semaine
 
NEMA 34, 650 oz-in holding torque
  
OMHT34-505
230.01
Stock: 1 semaine
 
NEMA 34, 849 oz-in holding torque
  
OMHT34-486
549.37
Stock: 5 semaines
 
NEMA 34, 1200 oz-in holding torque
  
OMHT34-506
319.37
Stock: 1 semaine
 
NEMA 34, 1260 oz-in holding torque
  
OMHT34-487
739.81
Stock: 1 semaine
 
NEMA 34, 1845 oz-in holding torque
Accessories
Cliquez pour agrandir / réduire une liste d'achat connexeOMPS150A24
OMPS150A24
Consultez le Service de ventes  
Stock: 
 
 
Stepper drive power supply for ST series,  24 VDC, 6.3A
  
OMPS300A48
Consultez le Service de ventes  
Stock: 
 
 
Stepper drive power supply for ST series, 48 VDC, 6.7A
  
HUB 444 DIN RAIL
Consultez le Service de ventes  
Stock: 
 
 
Multi-axis network hub with DIN rail mounting kit
  
MMI-01
Consultez le Service de ventes  
Stock: 
 
 
Operator Interface
  
OMRC-050
€243.68
Stock: 1 semaine
 
Motor regeneration clamp
  
Power Cord-SE
€12.18
Stock: 4 semaines
 
AC Power cord with stripped end termination
  
Power Cord-SE-M16
€17.27
Stock: 1 semaine
 
8' Power cord with M16 cable gland strain relief, 3x16 AWG, 250Vac max.
  
OMBOB-1
Consultez le Service de ventes  
Stock: 
 
 
Breakout box for I/O connector
  
ENC-ST-CA-10
Consultez le Service de ventes  
Stock: 
 
 
Encoder cable for ST drive, 3 m (10')
Cliquez pour agrandir / réduire une liste d'achat connexeOM-CONV-USB
OM-CONV-USB
€23.30
Stock: 1 semaine
 
USB to RS-232 Interface Converter; USB-A to DB9-male
Cliquez pour agrandir / réduire une liste d'achat connexeOM-PL-USBS
OM-PL-USBS
Consultez le Service de ventes  
Stock: 
 
 
USB to RS232 converter; works with Windows Vista and Windows 7.
  
OMG-USB-485-1
€174.02
Stock: 1 semaine
 
USB to RS-422/485/530 Interface Converter; USB-A to DB25-male
  
OMG-CA175
€19.40
Stock: 7 semaines
 
DB25F/9M cable (DB9 RS-422 pinout)
  
SI-PROG-CBL
€31.57
Stock: 1 semaine
 
Replacement programming cable (comes with drive)
  
DRIVE-CBL
Consultez le Service de ventes  
Stock: 
 
 
Replacement MMI and/or HUB communications cable (comes with MMI-01 and HUB 444)
  
DSUB-9-MF
Consultez le Service de ventes  
Stock: 
 
 
DIN rail interface module, 9-pin
  
DSUB-25-MF
Consultez le Service de ventes  
Stock: 
 
 
DIN rail interface module, 25-pin
  
DSUB-9-MF-CBL
€48.42
Stock: 1 semaine
 
DSUB cable, 9-pin, 2 m (6.6'), male/female connectors
  
DSUB-25-MF-CBL
€34.92
Stock: 7 semaines
 
DSUB cable, 25-pin, 2 m (6.6'), male/female connectors
Tous les Montants indiqués Dans EUR
Notez: Programming/serial configuration cable included. Programming/configuration software is a free download; click on "Software" icon below the picture. To see torque-speed curves for recommended motors, click on "Specs" above.
We noticed you are from the US. Visit your local site for regional offers and live support.